I search an engineer for the design and development of a orthopedic product. Project duration 2 weeks (2 weeks means 14 workdays) no weekends granted. The product is already covered by a provisional patent... (Budget: $250-750, Jobs: Electronics, Engineering, Manufacturing Design, Mechanical Engineering, Project Management)

You will be making a small portable magnetic reader that runs off a battery and has similar dimensions to 4 x 5 x 15mm . This magnetic card reader collects/stores tracks 1 and 2 on its 2mags of onboard memory... (Budget: $30-250, Jobs: Electrical Engineering, Electronics, Microcontroller, PCB Layout, Project Management)

The project is Nonpublic. Description can be read only by registered users. (Budget: $250-750)

On a local 10/100 base Network I need to send 8 Channels of uncompressed audio 96k-24bits provided from a Analog Devices ADAU1401A in TDM format (serial I2S stream of 8 Channel of audio 96k 32bits) from... (Budget: $250-750, Jobs: C Programming, Electronics, Microcontroller, PCB Layout)

I require a circuit and layout of PCB to allow 24 channel TTL Digital I/O from an embedded SBC to drive 250v power relay which can be situated up to 20m away. (Relay specs can be found at the following website: http://www.scr.com.tw/ssr-series_01.htm )... (Budget: $250-750, Jobs: Electronics, PCB Layout)

The project is Nonpublic. Description can be read only by registered users. (Budget: $30-250)

Looking for an engineer to design and build a proto of a long range Transmitter and receiver. Range: ~800 meters- Must be designed so that I do not need a FCC license... Transmitter-- size:... (Budget: $250-750, Jobs: Electrical Engineering, Electronics, Engineering, Microcontroller, PCB Layout)

I have researched a lot about this, I am not a programmer thats the only problem, exactly what i need is i want to start/Stop or see status of my Sprinklers at my home or office . The sprinkler is just an example to keep it simple... (Budget: $750-1500, Jobs: C Programming, Electronics, Engineering, Manufacturing, Product Design)

I need a person that can take my idea from a hand drawn representation to a working model. I have an idea for a new remote control, but I need to put together a engineering drawing so that I may get a... (Budget: $250-750, Jobs: Electrical Engineering, Electronics, Microcontroller)

The FPGA project is to porting a WLAN s PHY cores into a Xilinx FPGA development board (E.g Spartan 3A). Use of the public domain WLAN s PHY cores from Rice University s WARP project (http://warp.rice.edu/trac/wiki/OFDMReferenceDesign/Changelog),... (Budget: $250-750, Jobs: Electronics, Engineering, Matlab & Mathematica, Verilog / VHDL, Wireless)

The project is Nonpublic. Description can be read only by registered users. (Budget: $30-250)

I need to develop a gsm enabled standalone biometric attendance system. For this, I am planning to integrate Suprema SFM3500 fingerprint module with a gsm enabled board. Board can be Win CE or linux based... (Budget: $250-750, Jobs: Electronics, Embedded Software)

I am looking for a PLC programmer that knows well Siemens S7-300 controller. If you are using in every day work / or as a teacher PLC's this is a project for you. This project is to create a training... (Budget: $250-750, Jobs: Electrical Engineering, Electronics, Engineering, Microcontroller, PLC & SCADA)

You will be making a small portable magnetic reader that runs off a battery. This magnetic card reader collects/stores tracks 1 and 2 on its 2mags of onboard memory. The magnetic head and magnetic stripe will be ISO... (Budget: $1500-3000, Jobs: Electrical Engineering, Electronics, Microcontroller, PCB Layout, Project Management)

This project is very simple and straight forward. I would like to have a custom made numerical keypad key logger that will log incoming data from a 7-pin data ribbon sensor sililar to the one shown in pictures... (Budget: $750-1500, Jobs: Electrical Engineering, Electronics, Mechanical Engineering, Microcontroller, PCB Layout)

You are to design and prototype a Type 5 COMexpress module - extended form factor. http://www.smallformfactors.com/pdfs/Kontron.Cat06.pdf Applicants must have knowledge and prior experience of Intel chipsets and high speed circuit design... (Budget: min $5000, Jobs: Electrical Engineering, Electronics, Microcontroller, PCB Layout)

The project is Nonpublic. Description can be read only by registered users. (Budget: $750-1500)

The project is Nonpublic. Description can be read only by registered users. (Budget: $250-750)

I have designed a 2 slot PCI backplane to host a computer and an ADC card. The board is 2 layer (top and bottom), all the PCI signal lines are on top, bottom is almost entirely ground. The board works... (Budget: $250-750, Jobs: CAD/CAM, Electronics, PCB Layout)

WE WANT TO OUTSOURCE THE DEVELOPMENT OF HANDHELD TERMINAL WITH FOLLOWING SPECS: High Power 32Bit ARM 9 @ 200MHz Memory Flash Memory 256MB - extendable upto 2GB RAM Memory 128MB USB Memory... (Budget: $750-1500, Jobs: Electronics, Embedded Software, Linux, Microcontroller, Product Design)

We are looking for Fixed 802.16D WiMAX MAC development professionals. You should have experience in developing Base Station MAC and Subscriber station MAC and experience in getting it field tested. You... (Budget: min $5000, Jobs: Algorithm, Electronics, Matlab & Mathematica, Verilog / VHDL, Wireless)

I have this leopard board with a DM355 chip that is running on Linux Kernel 2.6.10 (Monta Vista Linux 4.0) http://designsomething.org/leopardboard/uploads/LeopardBoard_Hardware_Guide_V1.1.pdf I want... (Budget: $250-750, Jobs: Electronics, Embedded Software, Engineering, Linux, Microcontroller)